SARC INTERNATIONAL CONFERENCE – Proceedings
Papers
-
XPS Analysis of Heated Highly Hydrogenated DLC Surfaces
Kenji Yamada, Takahiro Bandou, Hirofumi Takikawa
Paper ID ID-ICSET-BNGK-210324-9066 · Pages 1
Download PDFAbstract
This study explored the structural transformations occurring in diamond-like carbon (DLC) films upon heating, as analyzed through X-ray photoelectron spectroscopy (XPS). Experimental samples were prepared from both hydrogenated amorphous carbon (a-C:H) and hydrogenated tetrahedral amorphous carbon (ta-C:H). The carbon 1s spectra were reduced from both sample surfaces by heating them to 600°C. These spectra were separated into two waveforms;the SP3 and the SP2 bonded components. In a-C:H, a decrease was observed in the componentwaveform with both component percentages remaining constant,while the ta-C:H samples exhibited a reduction in theSP2 bonded component. Next, when separated into four waveforms, the a-C:H sample showed adecrease in the bulk component of the SP3 and SP2, whereas the ta-C:H sampledemonstrated a reduction primarily in the bulk component of SP3 and the surface component of SP2. These findings highlight the distinct structural changes induced by annealing in different types of DLC samples, specifically a-C:H and ta-C:H. Keywords - Diamond-like carbon(DLC), hydrogenated amorphous carbon (a-C:H), hydrogenated tetrahedral amorphous carbon (ta-C:H), X-ray photoelectron spectroscopy(XPS)
-
Design of Zinc Sulphide Material-Based Field Effect Transistor with Physics of Semiconductor Devices
Mya Su Kyi, Maung Aye, Tin Tin Hla
Paper ID SA-AEEE-BNKK-240324-4409 · Pages 9–17
Download PDFAbstract
The paper presents the design of Zinc Sulphide (ZnS) material-based Field Effect Transistor (FET) with physics of semiconductor devices. The main research challenge is to estimate the physical properties of ZnS-based FET without using experimental setup in a laboratory and the research direction for solving this challenge is to implement the programming platform for evaluate the targeted properties by physics of semiconductor devices and MATLAB language. The switching characteristics for proposed ZnS-based FET with voltage and current characteristics from the specific physical parameters of the targeted semiconductor material in Group II and VI in a periodic table. After observing the theoretical results with numerical techniques, the developed ZnS-based FET could be utilized in the high-performance switching power electronic converter circuits. Keywords - Zinc Sulphide (ZnS), Field Effect Transistor, Physics of Semiconductor Devices, MATLAB, Numerical Analysis
-
Design and Structural Analysis of Main Shaft with Three Different Materials for Rice Polishing Machine
Thida Win, Htay Htay Win, Aung Ko Latt
Paper ID SA-IMEC-BNKK-240324-4420 · Pages 13–25
Download PDFAbstract
This paper focuses on the design and structural analysis of main shaft for rice polishing machine by changing three different materials. Failure of the main shaft is occurred due to tensile, shear, bending and torsional stresses. This is the major source of the main shaft failure of rice polishing machine. Failure of the main shaft can be reduced by choosing suitable material. The motor power of the machine is 1.5 hp and rotational speed is 1440 rpm. This motor uses v-belt transmission system to drive the main shaft. The diameter of the main shaft is 22mm.The number of belts is 2 belts. ASME code equation is used to design the main shaft for rice polishing machine. ANSYS 17.0 software is used to analyze the structural analysis of main shaft with material of AISI 1020, ASTM A514 structural steel, ASTM A220 Cast Iron. Theoretical and numerical von-Mises stress values are 58.6MPa and 60.647MPa. The theoretical and numerical effective strain values are 2.473×10-4 and 2.6857×10-4. Moreover, the von-Mises stress and effective strain value of AISI 1020 material is less than other two materials. The theoretical and numerical von-Mises stress values of the main shaft is less than the allowable stress of the main shaft. So the design of the main shaft is satisfied. Therefore, the suitable material of the main shaft for rice polishing machine is AISI 1020. Keywords - Main shaft, tensile strength, bending stress, von-Mises stress, effective strain
-
Design Optimization and Flow Analysis of Cross Flow Turbine (500 W)
Sandar Kyaw, War War Min Swe, Aung Kyaw Soe, Aung Ko Latt
Paper ID SA-IMEC-BNKK-240324-4421 · Pages 20–39
Download PDFAbstract
In a hydro-power project, water turbine is one of the most important parts of the generating of electricity. The main purposes of this thesis are to develop the living standard in rural areas and to reduce the use of non-renewable energy. Crossflow turbines are commonly used in low-head small hydro systems. A crossflow turbine is a unique type of hydro-turbine in that the flow passes twice through the runner. Therefore, the power is extracted in two stages. The feasibility of hydraulic turbine, theory of cross-flow turbine, detail design calculation, model design of 500 Watts Cross-Flow Turbine are described .This paper contains a complete set of detail drawings for manufacturing of a 500 Watts Cross-Flow Turbine. It can be used at sites which head is 1.5 m and flow rate is 0.045 m3/s. For the given capacity, the dimensions of turbine diameter and length are 330 mm and 295 mm. The performance analysis of Cross-Flow Turbine can be predicted by numerical analysis. The runner speed is 141 rpm and number of blades is 21 blades. The angle of nozzle inlet is 16° and the inlet blade angle is 30° respectively. The objective of this work is to characterize the two stage power transfer in the runner. Moreover, the purpose of this study is also both to test the performance of a low cost cross-flow turbine and to observe on the efficiency of a low cost Cross-flow turbine. The maximum efficiency of the turbine is 85%. The model design of this turbine consists of the preparing of blades, runner, nozzle and other components. All components of this turbine are made by mild steel. Keywords - Cross-Flow Turbine, Model design, two stage power, maximum efficiency.
-
EXPERIMENTAL INVESTIGATIONS TO EVALUATE SURFACE FATIGUE WEAR IN JOURNAL BEARING BY USING VIBRATION SIGNAL ANALYSIS
AMARNATH M, RAMACHANDRA C G, H. CHELLADURAI, P. SATEESH KUMAR, K. SATHOSH KUMAR
Paper ID IED-CEST-BNGK-240324-600A · Pages 27–53
Download PDFAbstract
Journal bearings are extensively used sliding contact machine elements to support radial / axial loaded rotors used in various applications viz. automobile crankshaft, turbine propeller shaft, rope conveyer, heavy duty electric motors. The primary reasons for failures of these bearings include unstable lubricant film, oil degradation, misalignment, etc. This paper describes the results of experimental investigations carried out to detect surface fatigue wear developed on load bearing the contact surfaces of journal bearing. The test bearing was subjected to fatigue load cycles over a period of 600 hours. The vibration signals were acquired from the journal bearing at regular interval of 100 hrs. These signals were post-processed by using the vibration analysis technique to obtain diagnostic information of wear propagated in the journal bearing system. Keywords - Fatigue, journal bearing, sound signals, vibration signals, wear
-
CONDITION MONITORING OF A CRITICAL MACHINE IN A TYRE MANUFACTURING INDUSTRY BY ANALYZING VIBRATION SIGNALS
RAMACHANDRA C G
Paper ID IED-CEST-BNGK-240324-601A · Pages 28–55
Download PDFAbstract
The machine performance level drops down over a period of time due to the wear and tear of its components. The early detection of an emergent fault becomes very vital in order to obtain the uninterrupted production in a plant. Maintenance is an activity which helps to keep the machine performance at an anticipated level, thereby ensuring the availability of the machine to perform its intended function. At present, a number of modern maintenance techniques are available such as preventive maintenance, predictive maintenance, condition based maintenance, total productive maintenance, etc. Condition based maintenance or condition monitoring is one such modern maintenance technique in which the machine condition or health is checked by the measurement of certain parameters such as sound level, temperature, velocity, displacement, vibration signals, etc. It can recognize most of the factors restraining the usefulness and efficacy of the total manufacturing unit. This research work is conducted on a Batch off Mill in a tyre production unit located in Southern Karnataka region. The health of the mill is assessed using amplitude of vibration as a parameter of measurement. Most commonly, the vibration level is assessed using various points on the machine bearing. The normal or standard level is fixed using the reference materials such as manuals or catalogues supplied by the manufacturers and also by referring vibration standards. The Rio-Vibro meter is placed in different locations on the batch off mill to record the vibration data. The data collected are analyzed to identify the malfunctioning components in the batch off mill and corrective measures are suggested. Keywords - Availability; Displacement; Vibration Sgnals; Rio-Vibro; Condtion Monitoring